brake

Rubber DOT approved brake hose for V35, V50 and V50 II, right front brake. Approximately 32.5 inches, female straight on one end, female low angle on... more info

Brake master cylinder spring as used on the following models: Moto Guzzi 1000 LM 1990 - 1994 Moto Guzzi 1000 LM 4 1985 - 1987 Moto Guzzi 1000 LM 5... more info

Master cylinder Y junction V35, V50, V50 II, V50 III, Monza, V65C,  V65SP, V65TT, V65 Lario, carbed Nevada 750s. One into two brake hose ... more info

800029058  Brembo anodized piston set fits F05 calipers as used on all the Guzzi small twins from the late 1970s until the 1990s. Also fitting... more info

New production!  "F09" caliper, twin opposed 48mm pistons. This is a reproduction caliper based on the discontinued Brembo F09 from the 1970s... more info

Reproduction of the Brembo F09 P09 P209 P2 09 caliper, for suitably equipped BMWmodels using this type of caliper where the caliper is mounted via... more info

Reproduction of the Brembo F09 P09 P209 P2 09 caliper, for suitably equipped BMWmodels using this type of caliper where the caliper is mounted via... more info

18659050, 34 1 11 458 211, 34111458211,   Brembo caliper 48mm seal kit for F09 caliper as used on the rear of some SP1000 models, and as... more info

48mm aluminum piston set for F09 brake caliper as used on the rear of some Guzzi models, and as sometimes used as an alternate brake caliper on the... more info

Four piston Brembo caliper, P4 30/34, left side, come complete with organic single pin brake pads.  The mounting points on these calipers have... more info

Four piston Brembo caliper, P4 30/34, right side, come complete with organic single pin brake pads.  The mounting points on these calipers have... more info

10mm internal diameter copper crush washer ( sealing washer ) for brake hose and brake banjo bolt applications. Altternative to the aluminum version... more info

GU25657001 Hydraulic front brake light switch as used on 850T, V50III, disc brake Eldorado, V65C, V65SP, V65TT, also listed for California II rear... more info

Brembo hollow brake pivot pin and stamped nut as used on rectangular master cylinders on many models from the 1980s through the 2000s.   ... more info

GU27661115 , 000046665  Hand brake master cylinder lid kit, forBrembo PS13- PS16 type 11, 12, 13 and 16mm master cylinders. Includes top, rubber... more info

Rubber boot for brake lever on Brembo PS 13 and PS 16 master cylinder,Quota, Jackal, California 1100 1994-1997, SPIII, California III, LeMans 1000... more info

This part is a Special Order item. Due to limited demand, we do not normally stock it. We will order the part directly from the... more info

GU28613345 GU17613350 New 300mm ferrous brake disc for many models including disk brake Eldorado, disk brake V7 Sport, 750S, S3, 850T, 850T3, T4,... more info

Brake disk bushing, brake rotor button, 1000S, SP III, California III, California 1100, LeMans 1000 all years LeMans IV and LeMans V, Strada This... more info

270mm stainless steel replacement brake disc, brake rotor, for LeMans 1000, all years LeMans IV and LeMans V, SP III, 1000 Strada, California III,... more info

Brake disk cup spring, brake rotor button spring, LeMans 1000 all years LeMans IV and LeMans V, 1000S, SP III, California 1100, California III,... more info

Genuine Brembo P2 F08 brake caliper, right side when used in front of the fork (see note below for alternate applications). These calipers are... more info

Brembo master cylinder repair kit for 12mm rectangular hand master cylinders , as used on Mille GT, LeMans 1000 1988 to 1991 (LeMans V), 1000S, SP... more info

Alternate brake light switch for models using the original hand master cylinder: V65 Lario, LeMans 1000 1984 to 1987 (LeMans IV), SP II, some... more info

300mm front brake disk outer ring for SP III, California III, California 1100 1994-1997, Strada. 5mm thick stainless steel European replacement disk.... more info

GU29667000  15mm rear master cylinder with integral reservoir. This type of rear master cylinder was used on all triple disk brake Guzzi big... more info

Black billet footpeg cover made of aluminum. Knurled surface for extra grip and more stable foot feel due to extra width. NOTE: This item is not... more info

1 into 1 aluminum brake line junction block with 6mm mouting hole. This items has standard 10mm x 1.00 thread pitch so accepts brake banjo bolts. Use... more info

GU30611460 Strada, California 1100, 1100 Sport carb, 1100 Sport injected, Centauro, Daytona RS, V11 Sport, V11 LeMans, Scura, Tenni, V11 Cafe, Naked,... more info

296mm front brake disk for Quota ES1100.  Note: product may vary from the photo.   more info

260mm stainless steel replacement rear brake disk, Quota 1100 ES 2nd series.  Note: Actual product may vary from the photo. This disk is... more info

270mm brake disk, rear on 1994-1997 California 1100, California III, Strada, 1993-2001 Nevada. This 270mm brake disc can be used on front or rear... more info

Brembo Original Equipment organic brake pad set for single retaining pin front calipers, also commonly used on numerous 90's Ducatis, Laverdas and... more info

Brembo carbon ceramic rear brake pad set for Moto Guzzi Quota 1100ES.  Latest Brembo street bike compound for superior performance. This pad... more info

Pin kit for single pin Brembo P4 30/34 C calipers as used on Daytona 1000, 1100 Sport carb, 1100 Sport injected, Centauro, Daytona RS, pre 2001 EV,... more info

Master cylinder repair kit for the 11mm front master cylinder on California 1100 carbed and injected, 1994 to 1997. GU30661460 more info

GU30661100 Front master cylinder on V11 Sport, V11 LeMans, Scura, Tenni, Rosso, Daytona 1000, Daytona Racing, Daytona RS, 1100 Sport carb, 1100 Sport... more info

GU30666900  OEM PS11C Brembo ~11mm bore rear master cylinder for Moto Guzzi, Aprilia, and Ducati models shown below. Ducati numbers 62540051A... more info

800057756  Brembo 110436241 master cylinder rebuild kit for PS11 B/C 11mm rear master cylinder using 40mm mounting. 1100 Sport carb, 1100 Sport... more info

GU30667030 Brembo rear master cylinder for Breva 750, Quota 1100ES and Quota 1000. ~13mm bore, 40mm bolt spacing . Alternate number: AP8113502 . Also... more info

GU30530526  Daytona 1000, Nevada and Nevada Club to 2003, California 1100, 1100 Sport carb, 1100 Sport injected, Centauro, Daytona RS, 1998-2000... more info

California 1100 1994-1997, 1998-2000California EV, Jackal, Bassa, California Special, 1100Sport Corsa, 1100 Sport Injected, V11 LeMans 2001-2004,... more info

Brass 3 way brake hose junction block or brake line union, original  to early spine frame models Daytona, Centauro, 1100 Sport, but useful ... more info

Brembo rear master cylinder, 15mm (~16mm) that was used on many models from late 1980s until after 2010. Some of the common models using this are:... more info

Aftermarket replacement rear brake disk for 1100 Sport carbureted models 1994-1996. This disc is stainless steel and made in France.  This part... more info

Brembo hand brake master cylinder with 16mm bore and remote reservoir, as used on 1996-1998 1100 Sport Injected. This master cylinder is the correct... more info

V35, V50, V50 II, V50 III, Monza, V65C, V65SP, V65TT, Lario. Brembo seals kit for 2 piston  F05 calipers as used front and rear on all early... more info

Brembo brake pad retaining pins kit for F05 calipers as found on all V35V50, V50 II, V50 III Monza, V65C, V65SP, V65TT, Lario. Also used on Ducati... more info

850T3, T4, T5, Convert, G5, California II, California III, California 1100, 850 LeMans, LeMans II, CX100, LeMans III, LeMans 1000 all years LeMans IV... more info

Low cost EMGO alternative to the rear brake light switch for V700 Ambassador, V750 Special 1969-1971, 850GT and Eldorado. Mounts basically the same... more info

OEM Ducati Brembo 11mm rear master cylinder (40mm spacing) used on the following Ducati models:  600 SS `95/97 750 SS `91 750 SS `92 750 SS `94... more info

079654116   Commonly used hydraulic, plug type, brake light switch. This switch is M10 with a 1.0 thread pitch. Hand and foot brake on 850T3,... more info

Spring retainer for single pin Brembo Goldline P4 30/34 C front caliper as used on Daytona 1000, 1100 Sport carb, 1100 Sport injected, Centauro,... more info

8A0062587  GU37613305 Genuine Brembo 320mm brake disc.  This is the early style full floating brake rotor with the round holes in the gold... more info

GU90271012  Snap ring for many applications including V7 Sport with 4 leading shoe front brake, 850GT, Eldorado with 4 leading shoe front brake,... more info

Snap ring circlip used on some late 80's and 90's model brake disks as well as on CARC model shift drums. Brake disk circlip on LeMans 1000 all years... more info

This is the little steel ball that actuates the brake light switch when you pull in the brake lever on most rectangular reservoir Brembo master... more info

Brake caliper shim, 0.5mm thickness, 10mm ID for centering brake calipers over brake disks more info

Brake caliper shim, 0.8mm thickness, 10mm ID for centering brake calipers over brake disks more info

Rear drum brake rod adjustment barrel for Nuovo Falcone, V700, Ambassador, 1969-1971 V750 Special, Eldorado, 850GT, V7 Sport, 750S, 850T. This part... more info

Brake disk bolt kit contains 6 bolts fitting many models beginning middle 1980s and extending to early 2000s.  These are 25mm long button head... more info

Double banjo bolt, 10mm x 1.00 fits into all Brembo brake components with 1.00 thread pitch, allows connection of 2 brake hoses to brake components.... more info

Goodridge double banjo bolt, 10 x 1.25 with crush washers. Secures two brake hoses with banjo fittings to one component. Includes 3 copper sealing... more info

Goodridge brake light switch, banjo bolt 1.00 pitch thread, single, with wires is a substitute for the original 14657050 switch. This brake switch... more info

Goodridge hydraulic brake light switch. This switch is a single banjo bolt type, meaning it replaces a standard banjo bolt and attaches one brake... more info

Goodridge brake light switch, double banjo bolt 1.00 pitch thread more info

Brake light switch that is a double banjo bolt with a 10mm x 1.25 thread pitch. Some Guzzi brake components (such as early junction blocks sometimes... more info

Brembo pistons and seals for 30/34 brake calipers.  No dust seals. more info

EBC Kevlar organic brake pads for F08 caliper, fits front and rear on all two valve per cylinder big twins (750, 850,1000,1100) before 1998, except... more info

EBC sintered Double-H compound rear brake pad set for CARC models:  Breva 1100, Griso 1100, Griso 1200 8V, Norge 1200 and 1200 8V,Sport 1200,... more info

EBC HH sintered brake pads, highest friction rating, for F08 caliper, fits front and rear on most all big twins (750, 850,1000,1100) before 1998,... more info

Fitting rear calipers on EV, EV Touring, Jackal, Bassa, California Special, Special Sport, California Stone, Stone Touring, Aluminum, Titanium,... more info

Fitting rear calipers on EV, EV Touring, Jackal, Bassa, California Special, Special Sport, California Stone, Stone Touring, Aluminum, Titanium,... more info

GU01654630, 01654630 replacement. EBC standard Kevlar organic front brake pads. These pads are retained in their calipers by 2 pins. It is important... more info

GU01654630, 01654630 replacement. EBC Sintered HH front brake pads. These pads are retained in their calipers by 2 pins. It is important to verify... more info

EBC HH sintered brake pads for two retainer pin rear brakes on some 2012, and 2013 and later 750s including: V7 Racer, V7 Stone, V7 Special, V7... more info

Breva 750, Nevada Classic IE 750 , V7 Classic, V7 Cafe, V7 Racer, V7 Stone, V7 Special 2004 -2011, single retaining pin. Note: Depending on market... more info

Breva 750, Nevada Classic IE 750 , V7 Classic, V7 Cafe, V7 Racer, V7 Stone, V7 Special. 2004-2011, single pad retaining pin . Note: Depending on... more info

EBC Kevlar organic brake pads used on many models 1978 -2005. Replacing Guzzi part numbers 19654600, 19654601 and 27654610. For front and rear F05... more info

EBC sintered brake pads used on many models 1978 -2005. Replacing Guzzi part numbers 19654600, 19654601 and 27654610. For front and rear F05... more info

EBC kevlar organic brake pad for F09 caliper. Often used as a more powerful brake caliper in custom applications, and originally used on the rear of... more info

Pair of EBC kevlar organic brake pads for early Brembo 4 piston calipers. These early "gold" 4 piston calipers use only 1 retainer pin to hold the... more info

Pair of EBC sintered brake pads for early Brembo 4 piston calipers. These early "gold" 4 piston calipers use only 1 retainer pin to hold the pad into... more info

Brake disk bolt kit for 850T3, Convert, G5 and 850T with dual disk conversion. Grade 8.8, this kit is not stainless. These 110mm bolts are necessary... more info

EBC 320mm Pro-Lite full floating brake disc for Antilock Braking System (ABS) equipped Moto Guzzis and Ducatis with disc mounted ABS rings.  ... more info

Stainless brake line kit for V65SP. Replace all your old rubber hoses with this kit. Brake hose kits replace original equipment rubber brake hoses in... more info

Stainless brake line kit for V65 Lario. Brake hose kits replace original equipment rubber brake hoses in original brake system configurations only.... more info

NOTE: This kit may come in black or clear coating/jacket (stainless look).   If the color matters to you, please email us BEFORE YOU PLACE YOUR... more info

Brembo MotorQuality Stainless brake line kit, 850T3, Convert, or G5 with California or Police handlebars.  Stainless brake hose kits replace... more info

Spiegler Brake hose kit Moto Guzzi 850 LeMans 1   Stainless brake line kit, 850 LeMans.  B rake hose kits replace original equipment rubber... more info

Stainless steel braided brake line kit for California II.  B rake hose kits replace original equipment rubber brake hoses in original brake... more info

Stainless brake line kit 850 LeMans III. Brake hose kits replace originalequipment rubber brake hoses in original brake system configurationsonly. If... more info

Stainless braided brake line kit for 850 LeMans II and CX100. Reduce flex and improve feel and braking efficiency. Brake hose kits replace original... more info

Stainless brake line kit SP II, some 850T5.  Brake hose kits replace original equipment rubber brake hoses in original brake system... more info

Stainless brake line kit LeMans 1000 (LM4). Reduce flex and improve feel and brakign efficiency. Brake hose kits replace original equipment rubber... more info

This part is a Special Order item. Due to limited demand, we do not normally stock it. We will order the part directly from the... more info

Brembo Motorquality branded stainless brake line kit for Mille GT, 1987 to 1991. Reduce flex and improve feel and braking efficiency. Brake hose kits... more info

Made by Fren Tubo Stainless steel braided brake line kit for 1977-1984 SP1000.   Translucent tinted plastic covering to protect from rubbing... more info

EBC Pro-lite full floating rotors, 270mm. Constructed from German stainless steel. These disks fit the 5 bolt brake pattern on 1986-1993 LeMans 1000,... more info

EBC Pro-lite full floating rotors, 300mm. Stainless steel brake disks on gold anodized aluminum carriers. These disks fit many 1970's and early '80s... more info